Our range of spare parts and accessories to suit Off Road Drift II Go Karts. A variety of parts for many models of Go Karts
$25.00
Air Filter cartridge for the 6.5hp 196cc engine for all Off Road Drift Go Karts. This is a replacement cartridge and can easily be installed
$25.00
Air Filter cartridge for the 9 hp 270 cc engine for all Off Road Drift Go Karts. This is a replacement cartridge and can easily be installed
$20.00
Air Filter housing for 6.5 hp 196 cc and 5.5 hp 168 cc Engines run on all Off Road Drift Go Karts. Does not include air filter cartridge. These can be easily installed at home. Made of black plastic$95.00
Staggered Spline rear axle for models GK200, GK200N, GK270N
Length 870 mm and Shaft Diameter is 27 mm Bearing seat to end of axle 165 mm Inner Spline Length 33 mm (118 mm from end of axle) Thread length 33 mm (85 mm from end of axle) Outer Spline length 32 mm (24 mm from end of axle) Thread length at end of axle 25 mm.
Thread 22 mm 1.5 p metric fine
Please contact me for a freight quote at info@gocartsaustralia.com.au or the item can be collected from my store
$115.00
Rear Drive Axle for Off Road Drift II Go Cart
Suits Models suffix LW
Axle Length 850 mm Bearing seat distance 145 mm from Axle end, Spline of axle length 90 mm (Axle thread at 26 mm from end of axle)
Please contact me for a freight quote at info@gocartsaustralia.com.au or the item can be collected from my store
$95.00
Rear Axle with keyway on drive side and spline on the brake side
Rear drive axle to suit models Drift II 6.5 hp 196 cc and Bulldog 270 cc 9 hp Karts
Please contact me for a freight quote at info@gocartsaustralia.com.au 0402229355 or the item can be collected from our store
$15.00
Rear Axle Bearings to suit Off Road Go Kart
Model older model
Sold Out
Rear Axle Bearings to suit Off Road Go Cart
Model GK200 GK200N & GK270N
Bearing 6205RS
Sold Out
Front Stub Axle Bearings to suit Off Road Go Cart
Model GK200 or GK200N or GK270N
Diameter 35 mm x 10 mm Centre 13 mm
Bearing 6003RS
$6.00
Bearing
Diameter 28 mm 8 mm width 12 mm centre hole
$15.00
Hydraulic Brake Caliper mounting Bracket
Caliper mounting holes 62 mm centre to centre
39 mm from hole centre to chassis mount
$40.00
Please note these are in stock
Text 0402229355 if you have problems ordering
Cable Brake Caliper for Drift II Off Road Go Carts to suit these style brake pads
Distance between mounting bracket holes centre to centre is 52mm
Please note hydraulic calipers are NOT a straight forward replacement for these brake Calipers
$120.00
Hydraulic Disc Brake assembly complete with caliper, hose and brake lever for butterfly steering wheel. Designed to increase brake capacity on Off Road Drift Go Karts. The brake pads contain no asbestos and can be easily replaced when required. Length of hydraulic hose approx. 140 cm from lever to caliper. Please note these are a replacement part and may require adaptations to fit some karts not originally fitted with Disc brakes
Note for replacement Lever has an 6 mm bolt to connect the hose and the Caliper is heavy duty cast with attachment holes at 40 mm centre to centre
$99.00
Heavy duty Hydraulic Disc Brake assembly complete with caliper, hose and brake lever for butterfly steering wheel. Designed to increase brake capacity on Off Road Drift Go Karts. The brake pads contain no asbestos and can be easily replaced when required. Length of hydraulic hose approx. 166 cm from lever to caliper. Please note these are a replacement part and may require adaptations to fit some karts not originally fitted with Disc brakes
Note for replacement Lever has an 8mm bolt to connect the hose and the Caliper is heavy duty cast with attachment holes at 63mm centre to centre
$99.00
Hydraulic Disc Brake assembly complete with caliper, hose and foot pedal leverage bracket for attachment to pedal control on Go Karts. Designed to increase brake capacity on all Off Road Drift Go Karts. The brake pads contain no asbestos and can be easily replaced when required. Length of hydraulic hose approx. 120 cm from foot pedal to caliper.
$35.00
Brake Rotor for Hydraulic Disc brakes
Diameter 160 mm 6 stud hole pattern Centre hole 39 mm Stud holes 25 mm apart centre to centre 3 mm thickness
$40.00
Brake Rotor for Hydraulic Disc brakes
Diameter 160 mm 6 stud hole pattern Centre hole 33 mm . Stud holes 22 mm apart centre to centre 2 mm thickness
$15.00
1 x pair Brake Pads to suit Cable type brake calipers. They contain No asbestos and these pads are easily replaced at home
$25.00
Brake Pads to suit Alloy Hydraulic brake calipers. These can be easily replaced at home and contain NO asbestos
Sold as a pair
$25.00
Brake Pads to suit Hydraulic disc brake calipers. These can be easily replaced at home and contain NO asbestos
Sold as a pair
$39.00
Front left hand Drum Brakes for Early Drift II Models. It comes complete with brake shoes and I do stock replacement brake shoes. Made from cast iron these are a well constructed unitSold Out
$89.00
Front Bumper Assemble. Attaches to most Off Road Drift II Go Carts. Easily to install
Distance between attachment Brackets centre to centre is.approx 245 mm..
Black Only
Please contact me for a freight quote 0402229355 or info@gocartsaustralia.com.au or the item can be collected from my store
$10.00
Rear swing arm bush
43 mm long with a 10 mm centre hole
$20.00
Brake Cable for butterfly steering wheel and standard brake calipers. This consists of an inner and outer cable
Approx. length of outer cable 120 cm
$25.00
Hydraulic brake hose
Length of hose 160 cm
Diameter of coupling hole 10 mm
2015-11 32 mm A072822 DOT SAE J101 /8 ID HL
Made in KH Hose
$25.00
Throttle Accelerator cable for the Bulldog Go Cart Foot Control
Approximate length 220 cm Outer Cable
$20.00
Throttle Accelerator cable for the butterfly steering wheel Go Cart
Approximate length 180 cm Outer Cable
For Drift II Go Karts
$39.00
Carbie to suit both 6.5 hp engines. Non adjustable fuel mixture screw Easily replaced at home
Does not come with engine gasket
$45.00
Carbie to suit both 9 hp engines. Non adjustable fuel mixture screw Easily replaced at home
Does not come with engine gasket
$35.00
Chain drive for 6.5 hp go carts
approx. 30 links 760 mm total length 41 Pitch
Chain Pitch Centre Pin 12.45 mm
Roller diameter 7.66 mm
Roller width 6.64 mm
Pin Thickness 3.93 mm
Side Bar Thickness 10.21 mm
Side Bar Thickness 1.45 mm
$39.00
Chain for the Bulldog 9 hp Engine
Length 900 mm
Chain Pitch Centre Pin 12.49 mm
Roller diameter 8.37 mm
Roller width 8 mm
Pin Thickness 4. mm
Side Bar width 10.53
Side Bar Thickness 1.58 mm
$55.00
Centrifugal Dry Clutch 10 tooth sprocket, fits a 19 mm shaft, diameter 110 mm, Length of centre shaft bush 59 mm and the internal clutch springs can be replaced
- The friction material & arrestor spring(s)
- The transmission plate & central shaft. (central shaft not shown. Picture below shows friction material and spring installed)
In the picture above you can see the friction material installed onto the transmission plate. You can see the transmission plate splines in the centre of the plate. The central shaft (not shown) slots into these splines and slides onto the crankshaft of the engine. It rotates with the engine because it is keyed and the key slots into the keyway on the crankshaft.
The drum sits over this material and is large enough so that the material does not contact the drum when it is fitted. You can rotate the drum freely when the unit is assembled as the friction material does not contact the drum.
As the speed of the crankshaft rotation increases (RPM increases) there is more and more centrifugal force on the friction material.
The spring holds them together in a tight circle and they do not touch the drum.
As the force pushing the friction material away from the centre increases to a point that it is greater than the force applied by the spring, the friction material starts to move outwards and contacts with the drum.
This begins to happen somewhere between 1500rpm and 1800rpm on the standard DRY CLUTCHES. At this point, the drum is still slipping on the friction material because the amount of force is not great enough to overcome the friction from the back wheels. The more weight, the more friction. When the drum slips, it creates heat. This is the biggest CON for the Dry Centrifugal Clutch.
NOTE: DRY CLUTCHES SHOULD NOT BE IDLED!
ONE MORE IMPORTANT THING TO NOTE IS THAT AFTER THE FIRST USE, SOME HEAT WILL INEVITABLY BE TRANSFERRED TO THE SPRING AND IT WILL STRETCH SLIGHTLY. FROM THIS POINT ON, AT IDLE, THE CLUTCH WILL SLOWLY BEGIN TO ENGAGE AT IDLE SPEED - THE HIGHER THE IDLE SPEED, THE MORE THE ENGAGEMENT WHICH WILL ACCELERATE WEAR.
At 2000rpm the friction material has so much centrifugal force applied to it that the spring can no longer arrest the material and it completely contacts the drum. This is considered it's FULLY ENGAGED rpm. Power is now transmitted directly through the chain to the rear drive sprocket and no further heat is created.
$15.00
Replacement centrifugal clutch spring
With the right tools it is easy to replace the spring in the clutch
$129.00
$129.00
$55.00
Drift Trike 10 mm thick Hardened Black Plastic Sleeves
Suit Tyres 22 cm to 23 cm Diameter
Sold as a PAIR
$359.00
Engine 6.5 hp 196 cc with Wet Clutch
Pull Start, Unleaded fuel, 4 stroke,
Dimensions (L x W x H) 37 cm x 31.5 cm x 33 cm approx Bore x Stroke 68 mm x 54 mm Shaft Length x Diameter 45.5 x 19.05 mm Keyway Size 4.78 x 16.36 mm Mounting Hole Dimensions (Diameter) M8 x 20 mm Compression Ratio 8.5:1 Max Power Output 4.8 KW Max Torque 10.8N.m/2500 rpm Type Single-Cylinder, 4-Stroke Displacement 196 cc, 2.1 Reduction Gearbox Unleaded Fuel, Tank 3.6 L Package Dimensions (L x W x H) 38 cm x 33 cm x 34 cm approx Package Weight 20 kg approx.
Please contact me for a freight quote on 0402229355 or info@gocartsaustralia.com.au or the item can be collected from my store
$259.00
Engine 6.5 horse power 196 cc. Pull Start, Unleaded fuel, 4 stroke,
Dimensions (L x W x H) 37 cm x 31.5 cm x 33 cm approx. Bore x Stroke 68 mm x 54 mm Shaft Length x Diameter 45.5 x 19.05 mm Keyway Size 4.78 x 16.36 mm Mounting Hole Dimensions (Diameter) M8 x 20 mm Compression Ratio 8.5:1 Max Power Output 4.8 KW Max Torque 10.8N.m/2500 rpm Type Single-Cylinder, 4-Stroke Displacement 196 cc Fuel Gasoline Fuel Tank 3.6L Package Dimensions (L x W x H) 38 cm x 32.5 cm x 34 cm approx. Package Weight 16 kg approx.
Please contact me for a freight quote at info@gocartsaustralia.com.au or text 0402229355 or the item can be collected from my store
$550.00
Engine 9hp 270 cc with Wet Clutch
Pull Start, Unleaded fuel, 4 stroke,
.
Please contact me for a freight quote on 0402229355 or info@gocartsaustralia.com.au or the item can be collected from our store on the Sunshine Coast QLD
$349.00
Engine 6.5 horse power 196 cc. Electric Start, Unleaded fuel, 4 stroke,
Dimensions (L x W x H) 37 cm x 31.5 cm x 33 cm approx. Bore x Stroke 68 mm x 54 mm Shaft Length x Diameter 45.5 x 19.05 mm Keyway Size 4.78 x 16.36 mm Mounting Hole Dimensions (Diameter) M8 x 20 mm Compression Ratio 8.5:1 Max Power Output 4.8 KW Max Torque 10.8N.m/2500 rpm Type Single-Cylinder, 4-Stroke Displacement 196 cc Fuel Gasoline Fuel Tank 3.6L Package Dimensions (L x W x H) 38 cm x 32.5 cm x 34 cm approx. Package Weight 16 kg approx.
Please contact me for a freight quote at info@gocartsaustralia.com.au or text 0402229355 or the item can be collected from my store
$230.00
Exhaust Muffler to suit 6.5 hp and 5.5 hp Engine for Drift II Go Kart, Bulldog and Black Thunder Go Karts
This is a Performance Upgrade and can increase HP up to around 9HP
$30.00
Exhaust Muffler to suit 6.5 hp and 5.5 hp Engine for Drift II Go Kart, Bulldog and Thunder Go Karts
$50.00
Exhaust Muffler to suit 6.5 hp and 5.5 hp Engine for Drift II Go Kart, Bulldog and Thunder Go Karts
Sold Out
Front Brush Frame with lugs to attach Roll Cage
Distance between mounting bolts Centre to Centre is 250 mm
Not all colours held in stock so please request the colour and we will endeavor to supply it
Please contact me for a freight quote 0402229355 or info@gocartsaustralia.com.au or the item can be collected from my store
$90.00
Front Brush Frame for the standard Drift II without roll cage This frame does not include lugs for roll cage
Distance between mounting bolts Centre to Centre is 250 mm
Colours will vary. We do not always carry every colour so please request the colour and we will endeavor to supply the colour of your choice
Please contact me for a freight quote 0402229355 or info@gocartsaustralia.com.au or the item can be collected from my store