Our range of spare parts and accessories to suit Off Road Drift II Go Karts. A variety of parts for many models of Go Karts
This collection is used by the OrderlyEmails app, to make product recommendations in your notification emails, which automatically update over time.
Note: This collection is "hidden", it is not be visible on your website.
$55.00
Centrifugal Dry Clutch 10 tooth sprocket, fits a 19 mm shaft, diameter 110 mm, Length of centre shaft bush 59 mm and the internal clutch springs can be replaced
- The friction material & arrestor spring(s)
- The transmission plate & central shaft. (central shaft not shown. Picture below shows friction material and spring installed)
In the picture above you can see the friction material installed onto the transmission plate. You can see the transmission plate splines in the centre of the plate. The central shaft (not shown) slots into these splines and slides onto the crankshaft of the engine. It rotates with the engine because it is keyed and the key slots into the keyway on the crankshaft.
The drum sits over this material and is large enough so that the material does not contact the drum when it is fitted. You can rotate the drum freely when the unit is assembled as the friction material does not contact the drum.
As the speed of the crankshaft rotation increases (RPM increases) there is more and more centrifugal force on the friction material.
The spring holds them together in a tight circle and they do not touch the drum.
As the force pushing the friction material away from the centre increases to a point that it is greater than the force applied by the spring, the friction material starts to move outwards and contacts with the drum.
This begins to happen somewhere between 1500rpm and 1800rpm on the standard DRY CLUTCHES. At this point, the drum is still slipping on the friction material because the amount of force is not great enough to overcome the friction from the back wheels. The more weight, the more friction. When the drum slips, it creates heat. This is the biggest CON for the Dry Centrifugal Clutch.
NOTE: DRY CLUTCHES SHOULD NOT BE IDLED!
ONE MORE IMPORTANT THING TO NOTE IS THAT AFTER THE FIRST USE, SOME HEAT WILL INEVITABLY BE TRANSFERRED TO THE SPRING AND IT WILL STRETCH SLIGHTLY. FROM THIS POINT ON, AT IDLE, THE CLUTCH WILL SLOWLY BEGIN TO ENGAGE AT IDLE SPEED - THE HIGHER THE IDLE SPEED, THE MORE THE ENGAGEMENT WHICH WILL ACCELERATE WEAR.
At 2000rpm the friction material has so much centrifugal force applied to it that the spring can no longer arrest the material and it completely contacts the drum. This is considered it's FULLY ENGAGED rpm. Power is now transmitted directly through the chain to the rear drive sprocket and no further heat is created.
$20.00
Throttle Accelerator cable for the butterfly steering wheel Go Cart
Approximate length 180 cm Outer Cable
For Drift II Go Karts
$40.00
Hydraulic Brake Lever with Fluid reservoir
No hose attached. For replacement of damaged hydraulic lever
PLEASE NOTE for replacement purposes the hose attachment bolt on this lever is an 8mm and normally has the heavy duty Cast brake caliper and 163 cm hose
Please check before ordering
$30.00
Pull Start to suit 6.5hp Engines
Replacement for 6.5hp Hybrid engine
$15.00
1 x pair Brake Pads to suit Cable type brake calipers. They contain No asbestos and these pads are easily replaced at home
$20.00
Brake Cable for butterfly steering wheel and standard brake calipers. This consists of an inner and outer cable
Approx. length of outer cable 120 cm
$20.00
Throttle lever for the right hand side of the butterfly steering wheel$49.00
Air Filter Cartridge Upgrade to suit 5.5 hp and 6.5 hp Engines
increased airflow and horsepower
60 mm inside diameter Adapter 61 mm outside diameter 25 mm inside diameter
Venturi Adapter [If you are looking to adapt this item to another filter or engine, stud spacing is 43 mm centre to centre, 6 mm studs. Centre of venturi has a hole 25.5 mm diameter. Outer diameter is 61 mm
$15.00
Replacement centrifugal clutch spring
With the right tools it is easy to replace the spring in the clutch
$129.00
$5.00
Drive Chain cut to length and sold by the 100 mm (10 cm) approx 4 links
Standard length of chain normally 30 links 770 mm long 41 Pitch
I have noticed some Karts require longer length chain so I now stock it by the roll and I stock chain joiners to suit
Chain drive for 6.5 hp go karts
Chain Pitch Centre Pin 12.45 mm
Roller diameter 7.66 mm
Roller width 6.64 mm
Pin Thickness 3.93 mm
Side Bar Thickness 10.21 mm
Side Bar Thickness 1.45 mm
$49.00
Hard plastic Go Cart seat to fit Off Road Drift II Go Carts
Measurements 50H x 50D x 40W
Please text suburb and post code to 0402229355 for freight quote
Postage measurements 65 x 30 x 49 Note only weights 2.5kg but cubes out to approx.
$50.00
Butterfly steering wheel for hand control Go Karts
35mm centre to centre mounting holes
$35.00
These Blue padded seat cover to suit all Drift Go Kart models. It is constructed of black and blue vinyl with padding to make the seats more comfortable. It has double stitching and a draw string to attach securely to plastic seat
$50.00
Exhaust Muffler to suit 6.5 hp and 5.5 hp Engine for Drift II Go Kart, Bulldog and Thunder Go Karts
$30.00
Rear axle sprocket chain drive for Off Road Drift II Go Carts
Diameter 198mm Centre hole 48mm 4 hole stud pattern approx. 49mm apart centre to centre
48 Tooth
$25.00
Brake Pads to suit Hydraulic disc brake calipers. These can be easily replaced at home and contain NO asbestos
Sold as a pair
$95.00
Staggered Spline rear axle for models GK200, GK200N, GK270N
Length 870 mm and Shaft Diameter is 27 mm Bearing seat to end of axle 165 mm Inner Spline Length 33 mm (118 mm from end of axle) Thread length 33 mm (85 mm from end of axle) Outer Spline length 32 mm (24 mm from end of axle) Thread length at end of axle 25 mm.
Thread 22 mm 1.5 p metric fine
Please contact me for a freight quote at info@gocartsaustralia.com.au or the item can be collected from my store
$45.00
Pull Start to suit 6.5hp Engines
Replacement for 6.5hp Hybrid engine
$15.00
Engine Kill Switch for steering wheel mounting
The latest replacement kill switch is more robust and comes complete with wiring loom. length of loom approx 150cm
$99.00
Hydraulic Disc Brake assembly complete with caliper, hose and foot pedal leverage bracket for attachment to pedal control on Go Karts. Designed to increase brake capacity on all Off Road Drift Go Karts. The brake pads contain no asbestos and can be easily replaced when required. Length of hydraulic hose approx. 120 cm from foot pedal to caliper.
$35.00
Road tyre 6inch 13x6.50-6 Tubeless 4 ply
Please text suburb and post code to 0402229355 for freight quote
$39.00
Black 8 inch wheel rim with a 3 hole stud pattern which do fit the Drift II Go Carts
Dimensions 200mm (7 inch) Diameter Width 130mm (5 inch)
Centre hole 54mm 3 studs 78mm apart centre to centre
Inter-changeable with most 6 inch Drift Go Kart rims
Please text suburb and post code to 0402229355 for freight quote
$49.00
Hydraulic Brake Caliper for Drift Go Karts. Consists of only the Caliper for the Hydraulic brake assembly. These callipers are replacement for carts already fitted with hydraulic brakes but are perfect for slowing these carts. They are fitted with brake pads and contain no asbestos and can be easily replaced when required.
Mounting holes 63 mm centre to centre
$20.00
Brake lever for cable brake calliper attached to the butterfly steering wheel$35.00
Brake Rotor for Hydraulic Disc brakes
Diameter 160 mm 6 stud hole pattern Centre hole 39 mm Stud holes 25 mm apart centre to centre 3 mm thickness
$129.00
$29.00
$59.00
Tyre 7 inch Tubeless 16x8-7 4 ply Directional tread tyres
10 psi operating pressure
Please contact me for a freight quote at info@gocartsaustralia.com.au or the item can be collected from my store
Please text suburb and post code to 0402229355 for freight quote
$29.00
$30.00
Front right hand stub axle. The right hand side is from sitting in the drivers seat.
Shaft Length 80mm Shaft diameter 15mm
Bearing 6001RS1
Does not include Wheel nut
$15.00
Oil dip stick for the wet clutch housing on 9hp Go Karts and 6.5hp Wet clutch engines
length 144mm 28mm thread
$15.00
Fuel cap petrol resistant plastic screw thread type
$25.00
Front Wheel Hub with bearings
106 mm Flange
2 x bearing 6003 RS
Sold as individual Hub NOT pair
$115.00
Rear Drive Axle for Off Road Drift II Go Cart
Suits Models suffix LW
Axle Length 850 mm Bearing seat distance 145 mm from Axle end, Spline of axle length 90 mm (Axle thread at 26 mm from end of axle)
Please contact me for a freight quote at info@gocartsaustralia.com.au or the item can be collected from my store
$25.00
Throttle Accelerator cable for the Bulldog Go Cart Foot Control
Approximate length 220 cm Outer Cable
$59.00
Hard plastic Go Cart seat to fit Off Road Drift II Go Carts
Measurements 50H x 50D x 40W
Please text suburb and post code to 0402229355 for freight quote
Postage measurements 65 x 30 x 49 Note only weights 2.5kg but cubes out to approx. 10kg
$30.00
Front left hand stub axle. The left side is from sitting in the drivers seat left hand side.
Shaft Length 68mm Shaft diameter 17mm
Bearing 6001 RS1
Does not include wheel nut
$120.00
Rear swing arm engine frame mount for Off Road Drift II Go Kart
To suit Model LWGK-50A
Dimensions Inner distance between swing arm connection arms to chassis
Please contact me for a freight quote 0402229355 or info@gocartsaustralia.com.au or the item can be collected from my store
$55.00
Round steering wheel for foot control Go Karts
30 cm Diameter 3 x mounting holes 37mm centre to centre
$220.00
Extension Chassis frame approx. 150 mm extension at the front of the chassis.
Internal distance between rear mounting brackets 420 mm and total distance between outside bracket to outside bracket is 535 mm
Distance from centre to centre of the front frame mounting bolts is 245 mm
As long as these measurements are the same it is a straight change over.
Contact 0402229355 for a freight quote or info@gocartsaustralia.com.au
$39.00
Chain for the Bulldog 9 hp Engine
Length 900 mm
Chain Pitch Centre Pin 12.49 mm
Roller diameter 8.37 mm
Roller width 8 mm
Pin Thickness 4. mm
Side Bar width 10.53
Side Bar Thickness 1.58 mm
$35.00
Brake Rotor for Hydraulic Disc brakes
Diameter 180 mm 6 stud hole pattern Centre hole 39 mm Stud holes 25 mm apart centre to centre 3 mm thickness
$55.00
Drift Trike 10 mm thick Hardened Black Plastic Sleeves
Suit Tyres 22 cm to 23 cm Diameter
Sold as a PAIR