Our range of spare parts and accessories to suit Off Road Drift II Go Karts and Bulldog Go Karts. A variety of parts for many models of Go Karts
Air Filter Cartridge Upgrade
$49.00
Air Filter Cartridge Upgrade to suit 5.5 hp and 6.5 hp Engines
increased airflow and horsepower
60 mm inside diameter Adapter 61 mm outside diameter 25 mm inside diameter
Venturi Adapter [If you are looking to adapt this item to another filter or engine, stud spacing is 43 mm centre to centre, 6 mm studs. Centre of venturi has a hole 25.5 mm diameter. Outer diameter is 61 mm
Axle A Staggered Spline
$95.00
Staggered Spline rear axle for models GK200, GK200N, GK270N
Length 870 mm and Shaft Diameter is 27 mm Bearing seat to end of axle 165 mm Inner Spline Length 33 mm (118 mm from end of axle) Thread length 33 mm (85 mm from end of axle) Outer Spline length 32 mm (24 mm from end of axle) Thread length at end of axle 25 mm.
Thread 22 mm 1.5 p metric fine
Please contact me for a freight quote at info@gocartsaustralia.com.au or the item can be collected from my store
Axle Kit
Sold Out
Axle kit for the home Go Kart builder. Comes complete with Axle, Front wheel hubs with bearings Rear wheel hubs Chain hub and rotor hub, 2 front wheel bushes and a keyway
One end is splined and one end has a keyway
Axle Length 870 mm
Bearings Front Stub Axle
$6.00
Bearing
Diameter 28 mm 8 mm width 12 mm centre hole
Belt Drive Torque Converter VS Belt 669
$39.00
Torque converter drive belt
18.8 mm wide single tapered one side 70 tooth 669 mm length
Brake Caliper Hydraulic Disc Hand lever Assemble Alloy Caliper
$130.00
Hydraulic Disc Brake assembly complete with caliper, hose and brake lever for butterfly steering wheel. Designed to increase brake capacity on Off Road Drift Go Karts. The brake pads contain no asbestos and can be easily replaced when required. Length of hydraulic hose approx. 140 cm from lever to caliper. Please note these are a replacement part and may require adaptations to fit some karts not originally fitted with Disc brakes
Note for replacement Lever has an 6 mm bolt to connect the hose and the Caliper is heavy duty cast with attachment holes at 40 mm centre to centre
Brake Caliper Hydraulic Disc Hand lever Assemble HEAVY DUTY
$110.00
Heavy duty Hydraulic Disc Brake assembly complete with caliper, hose and brake lever for butterfly steering wheel. Designed to increase brake capacity on Off Road Drift Go Karts. The brake pads contain no asbestos and can be easily replaced when required. Length of hydraulic hose approx. 166 cm from lever to caliper. Please note these are a replacement part and may require adaptations to fit some karts not originally fitted with Disc brakes
Note for replacement Lever has an 8mm bolt to connect the hose and the Caliper is heavy duty cast with attachment holes at 63mm centre to centre
Brake Caliper Hydraulic Foot Control assembly with reservoir
$110.00
Hydraulic Disc Brake assembly complete with caliper, hose and foot pedal leverage bracket for attachment to pedal control on Go Karts. Designed to increase brake capacity on all Off Road Drift Go Karts. The brake pads contain no asbestos and can be easily replaced when required. Length of hydraulic hose approx. 120 cm from foot pedal to caliper.
Brake Pads for Alloy Hydraulic Calipers
$25.00
Brake Pads to suit Alloy Hydraulic brake calipers. These can be easily replaced at home and contain NO asbestos
Sold as a pair
Brake Pads for Hydraulic Calipers
$25.00
Brake Pads to suit Hydraulic disc brake calipers. These can be easily replaced at home and contain NO asbestos
Sold as a pair
Bumper Front Assemble
$89.00
Front Bumper Assemble. Attaches to most Off Road Drift II Go Carts. Easily to install
Distance between attachment Brackets centre to centre is.approx 245 mm..
Black Only
Please contact me for a freight quote 0402229355 or info@gocartsaustralia.com.au or the item can be collected from my store
Bush Rear Swing Arm
$10.00
Rear swing arm bush
43 mm long with a 10 mm centre hole
Bushes Spacers Rear Axle
$10.00
Rear Axle spacers
24.8 mm inside diameter 32 mm outside diameter 17 mm width 3.3 mm thick
Cable Hydraulic Brake hose
$25.00
Hydraulic brake hose
Length of hose 160 cm
Diameter of coupling hole 10 mm
2015-11 32 mm A072822 DOT SAE J101 /8 ID HL
Made in KH Hose
Cap fuel Plastic Screw on
$15.00
Fuel cap petrol resistant plastic screw thread type
Chain Drive Joiner
$3.50
Drive Chain joiner for Drift II Go Kart. 420
For 6.5 hp engines We also have Chain to suit that can be purchased by the length
Chain Drive length to order 100 mm approx 4 links
$5.00
Drive Chain cut to length and sold by the 100 mm (10 cm) approx 4 links
Standard length of chain normally 30 links 770 mm long 41 Pitch
I have noticed some Karts require longer length chain so I now stock it by the roll and I stock chain joiners to suit
Chain drive for 6.5 hp go karts
Chain Pitch Centre Pin 12.45 mm
Roller diameter 7.66 mm
Roller width 6.64 mm
Pin Thickness 3.93 mm
Side Bar Thickness 10.21 mm
Side Bar Thickness 1.45 mm
Chain Drive Roller Chain for 6.5 hp Engine
$35.00
Chain drive for 6.5 hp go carts
approx. 30 links 760 mm total length 41 Pitch
Chain Pitch Centre Pin 12.45 mm
Roller diameter 7.66 mm
Roller width 6.64 mm
Pin Thickness 3.93 mm
Side Bar Thickness 10.21 mm
Side Bar Thickness 1.45 mm
Chain Drive Roller Chain for 9 hp Engine
$39.00
Chain for the Bulldog 9 hp Engine
Length 900 mm
Chain Pitch Centre Pin 12.49 mm
Roller diameter 8.37 mm
Roller width 8 mm
Pin Thickness 4. mm
Side Bar width 10.53
Side Bar Thickness 1.58 mm
Clutch Dry Centrifigal
$59.00
Centrifugal Dry Clutch 10 tooth sprocket, fits a 19 mm shaft, diameter 110 mm, Length of centre shaft bush 59 mm and the internal clutch springs can be replaced
- CLC3512.jpg (7.36 KiB) Viewed 2123 times
- The friction material & arrestor spring(s)
- InnerB.jpg (6.68 KiB) Viewed 2122 times
- The transmission plate & central shaft. (central shaft not shown. Picture below shows friction material and spring installed)
- Inner.jpg (15.72 KiB) Viewed 2122 times
In the picture above you can see the friction material installed onto the transmission plate. You can see the transmission plate splines in the centre of the plate. The central shaft (not shown) slots into these splines and slides onto the crankshaft of the engine. It rotates with the engine because it is keyed and the key slots into the keyway on the crankshaft.
The drum sits over this material and is large enough so that the material does not contact the drum when it is fitted. You can rotate the drum freely when the unit is assembled as the friction material does not contact the drum.
As the speed of the crankshaft rotation increases (RPM increases) there is more and more centrifugal force on the friction material.
The spring holds them together in a tight circle and they do not touch the drum.
As the force pushing the friction material away from the centre increases to a point that it is greater than the force applied by the spring, the friction material starts to move outwards and contacts with the drum.
This begins to happen somewhere between 1500rpm and 1800rpm on the standard DRY CLUTCHES. At this point, the drum is still slipping on the friction material because the amount of force is not great enough to overcome the friction from the back wheels. The more weight, the more friction. When the drum slips, it creates heat. This is the biggest CON for the Dry Centrifugal Clutch.
NOTE: DRY CLUTCHES SHOULD NOT BE IDLED!
ONE MORE IMPORTANT THING TO NOTE IS THAT AFTER THE FIRST USE, SOME HEAT WILL INEVITABLY BE TRANSFERRED TO THE SPRING AND IT WILL STRETCH SLIGHTLY. FROM THIS POINT ON, AT IDLE, THE CLUTCH WILL SLOWLY BEGIN TO ENGAGE AT IDLE SPEED - THE HIGHER THE IDLE SPEED, THE MORE THE ENGAGEMENT WHICH WILL ACCELERATE WEAR.
At 2000rpm the friction material has so much centrifugal force applied to it that the spring can no longer arrest the material and it completely contacts the drum. This is considered it's FULLY ENGAGED rpm. Power is now transmitted directly through the chain to the rear drive sprocket and no further heat is created.
Clutch Wet for 6.5 hp Engine
$129.00
- 2.1 Reduction Oil bath clutch
- For 6.5 hp 196 cc Wet clutch engine
- Fits a 19 mm shaft
- Gasket not included
- 14 Tooth
Clutch Wet for 9 hp Engine
$129.00
- 2.1 Reduction Oil bath clutch
- To fit 25 mm shaft
- 14 Tooth
DRIFT Trike SLEEVES to suit 22 -23 cm Tyres Pair
$60.00
Drift Trike 10 mm thick Hardened Black Plastic Sleeves
Suit Tyres 22 cm to 23 cm Diameter
Sold as a PAIR
Engine 6.5 hp 196 cc with Wet Clutch
$359.00
Engine 6.5 hp 196 cc with Wet Clutch
Pull Start, Unleaded fuel, 4 stroke,
Dimensions (L x W x H) 37 cm x 31.5 cm x 33 cm approx Bore x Stroke 68 mm x 54 mm Shaft Length x Diameter 45.5 x 19.05 mm Keyway Size 4.78 x 16.36 mm Mounting Hole Dimensions (Diameter) M8 x 20 mm Compression Ratio 8.5:1 Max Power Output 4.8 KW Max Torque 10.8N.m/2500 rpm Type Single-Cylinder, 4-Stroke Displacement 196 cc, 2.1 Reduction Gearbox Unleaded Fuel, Tank 3.6 L Package Dimensions (L x W x H) 38 cm x 33 cm x 34 cm approx Package Weight 20 kg approx.
Please contact me for a freight quote on 0402229355 or info@gocartsaustralia.com.au or the item can be collected from my store
Engine 9 hp 270 cc with Wet Clutch
$550.00
Engine 9hp 270 cc with Wet Clutch
Pull Start, Unleaded fuel, 4 stroke,
.
Please contact me for a freight quote on 0402229355 or info@gocartsaustralia.com.au or the item can be collected from our store on the Sunshine Coast QLD
Frame Bulldog Independent Front Suspension
$399.00
Independent Front suspension for Bulldog Go Karts with foot controls. Comes complete with air shocks,. Distance between mounting holes 245 mm.
BLACK ONLY
Please request at freight quote to 0402229355 or info@gocartsaustralia.com.au with post code and suburb
Frame Chassis Extension Frame
$220.00
Extension Chassis frame approx. 150 mm extension at the front of the chassis.
Internal distance between rear mounting brackets 420 mm and total distance between outside bracket to outside bracket is 535 mm
Distance from centre to centre of the front frame mounting bolts is 245 mm
As long as these measurements are the same it is a straight change over.
Contact 0402229355 for a freight quote or info@gocartsaustralia.com.au
Frame Front Brush Frame suits Roll Cage attachment
$110.00
Front Brush Frame with lugs to attach Roll Cage
Distance between mounting bolts Centre to Centre is 250 mm
Not all colours held in stock so please request the colour and we will endeavor to supply it
Please contact me for a freight quote 0402229355 or info@gocartsaustralia.com.au or the item can be collected from my store
Frame Roll Bar
$30.00
Roll bar frame
10mm Mounting holes with a total distance apart of 40 cm
Centre mounting hole 20 cm from each side
Total height of 28 cm
Frame Standard Drift II
$169.00
Standard Centre Frame for Drift II Go Karts
Front end Mounting bolts 245 mm centre to centre
Rear swing Arm Mounting brackets 430 mm internal measurement
Please text 0402229355 for a freight quote
Gasket Carburetor
$15.00
rubber carburetor /engine gasket 6.5hp 5.5hp engines
Go Kart BULLDOG 270 cc 9 hp Front Suspension BLACK with EPA engine
Sold Out
The BULLDOG 270 cc 9 hp BLACK
Note this for a BLACK coloured Go Kart with latest EPA engine
270cc 9 horse power 4 stroke engine with wet clutch, Hydraulic Disc brakes, Foot pedal controls, Front independent suspension with air shock absorbers, 6 inch tubeless tyres all round, 3 point Harness seat belt, Chain drive, Maximum speed approx. 55 klms the engine can be governed to reduce top speed. GK270N This kart comes with the extension frame which gives an approx extra 140 mm extra leg room Please contact me for a freight Quote at 0402229355 or info@gocartsaustralia.com.au or the Kart can be collected from our Store
The box dimensions are 120 cm x 98 cm x 62 cm 120 kg
Dimensions assembled 200 cm L x 99 cm W x 85 cm H
Go Kart BULLDOG 270 cc 9 hp Front Suspension BLACK with Torque Converter
Sold Out
The BULLDOG 270 cc 9 hp BLACK
Note this for a BLACK coloured Go Kart with latest EPA engine
270cc 9 horse power 4 stroke engine with belt drive torque converter, Hydraulic Disc brakes, Foot pedal controls, Front independent suspension with air shock absorbers, 6 inch tubeless tyres all round, 3 point Harness seat belt, Chain drive, Maximum speed approx. 55 klms the engine can be governed to reduce top speed. GK270N This kart comes with the extension frame which gives an approx extra 140 mm extra leg room Please contact me for a freight Quote at 0402229355 or info@gocartsaustralia.com.au or the Kart can be collected from our Store
The box dimensions are 120 cm x 98 cm x 62 cm 120 kg
Dimensions assembled 200 cm L x 99 cm W x 85 cm H
Go Kart BULLDOG 270 cc 9 hp Front Suspension RED with EPA engine
$1,799.00
The BULLDOG 270 cc 9 hp RED with latest EPA engine
Note this for a RED coloured Go Kart
270 cc 9 horse power 4 stroke engine with wet clutch, Hydraulic Disc brakes, Foot pedal controls, Front independent suspension with air shock absorbers, 6 inch tubeless tyres all round, 3 point Harness seat belt, Chain drive, Maximum speed approx. 55 klm the engine can be governed to reduce top speed. GK270N This kart comes with the extension frame which gives an approx extra 140 mm extra leg room Please contact me for a freight Quote at 0402229355 or info@gocartsaustralia.com.au or the Kart can be collected from our Store
The box dimensions are 120 cm x 98 cm x 62 cm 120 kg
Dimensions assembled 200 cm L x 99 cm W x 85 cm H
Go Kart BULLDOG 270 cc 9 hp Front Suspension RED with Torque Converter
$1,899.00
The BULLDOG 270 cc 9 hp RED with latest EPA engine
Note this for a RED coloured Go Kart
270 cc 9 horse power 4 stroke engine with torque converter, Hydraulic Disc brakes, Foot pedal controls, Front independent suspension with air shock absorbers, 6 inch tubeless tyres all round, 3 point Harness seat belt, Chain drive, Maximum speed approx. 55 klm the engine can be governed to reduce top speed. GK270N This kart comes with the extension frame which gives an approx. extra 140 mm extra leg room Please contact me for a freight Quote at 0402229355 or info@gocartsaustralia.com.au or the Kart can be collected from our Store
The box dimensions are 120 cm x 98 cm x 62 cm 120 kg
Dimensions assembled 200 cm L x 99 cm W x 85 cm H
Go Kart BULLDOG 270cc 9hp Front Suspension BLUE
$1,799.00
The BULLDOG 270 cc 9 hp BLUE with Extension Frame
Note this is for a BLUE coloured Go Kart
270 cc 9 horse power 4 stroke engine with wet clutch, Hydraulic Disc brakes, Foot pedal controls, Front independent suspension with air shock absorbers, 6 inch tubeless tyres all round, 3 point Harness seat belt, Chain drive, Maximum speed approx. 55 klm the engine can be governed to reduce top speed. GK270N. This kart comes with the Extension frame which gives an extra 140 mm extra leg room Please contact me for a freight Quote at 0402229355 or info@gocartsaustralia.com.au or the Kart can be collected from our Store
The box dimensions are 120 cm x 98 cm x 62 cm 120 kg
Go Kart BULLDOG 270cc 9hp Front Suspension, Torque Converter BLUE
$1,899.00
The BULLDOG 270 cc 9 hp BLUE with Extension Frame
Note this is for a BLUE coloured Go Kart
270 cc 9 horse power 4 stroke engine with belt drive torque converter, Hydraulic Disc brakes, Foot pedal controls, Front independent suspension with air shock absorbers, 6 inch tubeless tyres all round, 3 point Harness seat belt, Chain drive, Maximum speed approx. 55 klm the engine can be governed to reduce top speed. GK270N. This kart comes with the Extension frame which gives an extra 140 mm extra leg room Please contact me for a freight Quote at 0402229355 or info@gocartsaustralia.com.au or the Kart can be collected from our Store
The box dimensions are 120 cm x 98 cm x 62 cm 120 kg
Go Kart Drift II 6.5 hp 196 cc BLACK with EPA engine
$1,099.00
GO KART
Note this is for a BLACK coloured Go Kart with latest EPA engine
The standard but most popular Go Kart. Great for the kids yet the adults can still jump on and have a go. It has a 6.5 hp 196 cc 4 stroke engine with pull start. It has a centrifugal clutch, uses unleaded fuel and has a top speed of approx. 35 to 45 kph. This model has hydraulic disc brakes and a butterfly steering wheel with lever throttle and brake controls. The engines can be governed to reduce the top speed if required
Please contact me for a freight quote at info@gocartsaustralia.com.au or the cart can be collected from my store or text your post code and suburb to 0402229355
Box Dimensions 85 kg 110 cm x 98 cm x 53 cm
Go Kart Drift II 6.5 hp 196 cc BLACK with TORQUE CONVERTER
$1,299.00
GO KART
Note this is for a BLACK coloured Go Kart with latest EPA engine
The standard but most popular Go Kart. Great for the kids yet the adults can still jump on and have a go. It has a 6.5 hp 196 cc 4 stroke engine with pull start. It has a TORQUE CONVERTER, uses unleaded fuel and has a top speed of approx. 35 to 45 kph. This model has hydraulic disc brakes and a butterfly steering wheel with lever throttle and brake controls. The engines can be governed to reduce the top speed if required. This model is ideal for the younger children, allowing slower speeds without over heating the clutch
Please contact me for a freight quote at info@gocartsaustralia.com.au or the cart can be collected from my store or text your post code and suburb to 0402229355
Box Dimensions 85 kg 110 cm x 98 cm x 53 cm
Go Kart Drift II 6.5 hp 196 cc BLUE with new EPA engine
$1,099.00
BLUE GO KART
Note this is for a BLUE Go Kart with latest EPA engine
The standard but most popular Go Kart. Great for the kids yet the adults can still jump on and have a go. It has a 6.5 hp 196 cc 4 stroke engine with pull start. It has a dry centrifugal clutch, uses unleaded fuel and has a top speed of approx. 35 to 45 km. This model has hydraulic disc brakes and a butterfly steering wheel with lever throttle and brake controls. The engines can be governed to reduce the top speed if required
Please contact me for a freight quote on 0402229355 or info@gocartsaustralia.com.au or the cart can be collected from my store
Box Dimensions 85 kg 110 cm x 98 cm x 53 cm
Go Kart Drift II 6.5 hp 196 cc BLUE with TORQUE CONVERTER
$1,299.00
BLUE GO KART
The standard but most popular Go Kart. Great for the kids yet the adults can still jump on and have a go. It has a 6.5 Hp 196 cc 4 stroke engine with pull start. It has a TORQUE CONVERTER, uses unleaded fuel and has a top speed of approx. 35 km. This model has hydraulic disc brakes and a butterfly steering wheel with lever throttle and brake controls. The engines can be governed to reduce the top speed if required. This model is ideal for the younger children, allowing slower speeds without over heating the clutch
Please contact me for a freight quote on 0402229355 or info@gocartsaustralia.com.au or the cart can be collected from my store
Box Dimensions 85 kg 110 cm x 98 cm x 53 cm
Go Kart Drift II 6.5 hp 196 cc RED with new EPA engine
Sold Out
RED GO KART
Note this is for a RED coloured Go Kart with latest EPA engine
The standard but most popular Go Kart. Great for the kids yet the adults can still jump on and have a go. It has a 6.5 hp 196 cc 4 stroke engine with pull start. It has a dry centrifugal clutch, uses unleaded fuel and has a top speed of approx. 35 to 45 km. This model has hydraulic disc brakes and a butterfly steering wheel with lever throttle and brake controls. The engines can be governed to reduce the top speed if required
Please contact me for a freight quote on 0402229355 or info@gocartsaustralia.com.au or the cart can be collected from my store
Box Dimensions 85 kg 110 cm x 98 cm x 53 cm
Go Kart Drift II 6.5 hp 196 cc RED with TORQUE CONVERTER
$1,299.00
RED GO KART
Go Kart with latest EPA engine & torque Converter
The standard but most popular Go Kart. Great for the kids yet the adults can still jump on and have a go. It has a 6.5 hp 196 cc 4 stroke engine with pull start. It has a TORQUE CONVERTER, uses unleaded fuel and has a top speed of approx. 35 to 45 km. This model has hydraulic disc brakes and a butterfly steering wheel with lever throttle and brake controls. The engine can be governed to reduce the top speed if required. This model is ideal for the younger children, allowing slower speeds without over heating the clutch
Please contact me for a freight quote on 0402229355 or info@gocartsaustralia.com.au or the cart can be collected from my store
Box Dimensions 85 kg 110 cm x 98 cm x 53 cm
Housing Wet Clutch 6.5 HP engine
$60.00
Front and rear housing to suit 6.5 hp wet clutch engine
Housing Wet Clutch 9HP engine
$60.00
Front and rear housing to suit 9hp wet clutch engine
Hub Front Wheel
$25.00
Front Wheel Hub with bearings
106 mm Flange
2 x bearing 6003 RS
Sold as individual Hub NOT pair